Sorry, you need to enable JavaScript to visit this website.
hamburger overlay

Frequently Asked Questions

Test Strips and control tests

No, check the use by date on the test strip container. Do not use test strips past the use by date.

Performing a control test lets the user know the meter and test strips are working properly. Perform a control test when:

  • You open a new test strip box
  • You left the test strip container open
  • You think the test strips are damaged
  • You want to check the meter and test strips
  • The test strips were stored in extreme temperatures, humidity, or both
  • You dropped the meter
  • Your test result does not match how you feel
  • You want to check if you are performing the test correctly

The Accu-Chek Performa blood glucose meter automatically recognises Accu-Chek Performa Control Solutions, so running a control test is easier than ever. First, wipe the tip of the control bottle. Then put the meter on a flat surface, insert the strip, and squeeze a drop of the control solution onto the front edge of the test strip. A result appears with a flashing “L”. Press one of the arrow keys once to indicate a Level 1 control test or twice to indicate Level 2. Press the ON/OFF button to set the level in the meter. The control result and “OK” alternate in the display if the result is in range.

In the same way that fresh blood should always be used for monitoring, fresh control solution should be used to prevent a contaminated control drop. Control solution should always be wiped from the tip of the bottle so that only what is in the bottle itself is used for the test.

Control test values will not be in the user-accessible memory. However, they will be stored in the downloadable memory.

No. Accu-Chek Performa blood glucose meters are designed exclusively for use with Accu-Chek Performa test strips.

Special features

To mark a test result or set a post-meal reminder:

  1. Perform a test. The result appears on the display.
  2. Leave the test strip in the meter. Press and release or to toggle through test result markers and the post-meal reminder.
    • Pre -meal marker
    • Pre-meal marker with post-meal reminder
    • Post-meal marker
    • General marker
  3. When the marker or test reminder you wish to select appears on the display, remove the test strip from the meter.

Yes. If the post-meal reminder marker is selected, the meter will beep 2 hours after the pre-meal test to remind you to perform a post-meal test. You can change the pre-meal test reminder to 1 hour after the pre-meal test.

You can set up to 4 test reminders per day. At the set reminder time, the meter will beep every 2 minutes, up to 3 times per reminder. The meter will not beep if the meter is on at the reminder time, or if a test has been run within 30 minutes of the reminder time.

Yes. Simply go into setup mode and turn the beeper off.

The meter is compatible with all Accu-Chek data management tools, including the Accu-Chek 360o diabetes management system.

With the new Accu-Chek Performa blood glucose meters, it is not necessary to delete stored results. Once 500 blood sugar (glucose) results are in the memory, adding a new result causes the oldest one to be deleted.

No, the meter will no longer provide an automatic warning message telling you that your vial of test strips will soon expire or lock you out once they have expired.

To mark a result or set a post-meal reminder:

  1. Perform a test. The result appears on the display.
  2. Leave the test strip in the meter. Press and release or to toggle through test result markers and the post-meal reminder:
    • Pre -meal marker
    • Pre-meal marker with post-meal reminder
    • Post-meal marker
    • General marker
  3. When the marker or reminder you wish to select appears on the display, remove the test strip from the meter.

There are three types of averages: general, pre-meal and post-meal. To view results and averages, press and release left and right arrows to view stored results. The most recent test result appears on the display.

  • Press the left arrow to view previous test results from newest to oldest.
  • Press the right arrow to view 7, 14, and 30 day general averages
  • Continue to press the right arrow to view 7-, 14-, 30- and 90-day pre-meal and post-meal averages

Meter care and batteries

Watch this short video to see how easy it is to set the date and time.

https://youtu.be/R8tSbZA-W9c

Your meter comes with the batteries already installed and a preset time and date. You may need to change the time to match your time zone or, if you live in a state that observes daylight saving time, to reflect the time change.

To change these settings:

  1. Press and release the On/Off button to turn the meter on. The flashing test strip symbol appears. NOTE: If this is the first time your meter has been turned on, it will automatically enter the set-up mode, and "Set-up" and the hour will flash on the display. Skip to Step 3 to change the time or, if the date and time are correct, press and hold the On/Off button to exit the set-up mode.
  2. To enter the set-up mode, press and hold the On/Off button for about four seconds. “Set-up” and the hour flash on the display.
  3. Press and release the arrows to decrease or increase the hour. Press and hold the arrows to scroll faster.
  4. Press and release the On/Off button to set the hour. The minutes flash.
  5. Repeat steps 3 and 4 to set the minutes, AM/PM, month, day and year. The flashing field is the one you are changing.

Once you set the correct time and date, press and hold the On/Off button until the flashing test strip symbol appears.

Your battery should last for approximately 2,000 tests.

Make sure you have a new 3-volt, lithium battery, number CR2032, to insert. Open the battery door on the back of the meter, remove the old battery for at least 20 seconds, and press any button on the meter. Insert the new battery with the “+” sign facing out. Snap the battery door back into place. Press the on/off button, and the meter will beep. Setup and hour are flashing on the display. If the date and time are correct, press and hold the on/off button for about 4 seconds. Release the button, and you’re done.

The meter uses 1 3-volt lithium coin cell battery (type CR 2032) found in many stores.

The meter includes an additional internal battery that retains the time and date for up to 72 hours. So when the battery is changed, no memory is lost.

Clean and disinfect your meter once a week or any time blood gets on the meter. You should also clean the meter before allowing anyone else to handle it.

Cleaning is simply removing dirt from the meter, while disinfecting refers to removal of most but not all, disease-causing and other types of microorganisms.

  • 70% isopropyl alcohol
  • Mild dishwashing liquid mixed with water

10% household bleach solution (1 part bleach plus 9 parts water) made the same day

Be sure to clean the areas around slots and openings, while being careful not to get any moisture in them. You should also wipe down the entire meter surface, including the meter display.

Visit your meter's Screen Messages page for a list of messages and definitions or download the User Manual (insert appropriate link) for your meter.

Testing blood sugar (Glucose)

There are a few ways you can improve blood flow and make blood glucose testing easier: Warm your fingers by washing with warm, soapy water, then rinse and dry completely. Let your arm hang down at your side to increase blood flow to the fingertips. Grasp finger just below the joint closest to the fingertip and massage gently toward tip of finger, then squeeze for 3 seconds. Use an Accu-Chek lancing device set to the right penetration depth for your skin type. Refer to your User's Guide for additional information.

It's a small sample—just 0.6 microlitre.

The system automatically detects when enough blood has been applied to the strip and begins the test, even if some yellow is still visible. The only time you need to apply more blood is when the blood drop symbol continues to flash in the display.

An E4 error message will display on the meter, indicating not enough blood was drawn into the test strip for measurement or blood was applied after the test had started. You should discard the test strip and repeat the blood glucose test.

Yes. In addition to the fingertip, you can collect blood samples from the palm, forearm or upper arm. Talk with your healthcare professional before deciding if alternate site monitoring is right for you.

Your Accu-Chek lancing device has a special plastic cap designed for monitoring on other areas of the body. Talk with your healthcare professional before deciding if alternate site monitoring is right for you.

Note: Do not use the special plastic cap when monitoring at the fingertip. Follow the steps for fingertip monitoring, with a few differences:

  • Use the clear or gray cap.
  • You may need a deeper setting. Try 3 for your palm or 5-1/2 for your forearm or upper arm. (These are suggested settings; yours may differ.)
  • Press the opening of the clear or gray cap firmly against a fleshy area of the non-fingertip site. Press the lancing device up and down in a slow pumping motion to assist the flow of blood.
  • Keep steady pressure on the area, then press and release the plunger. Do not be afraid to apply pressure to the area with the lancing device to assist the flow of blood. Continue to press the cap against the site for a few seconds to allow blood to come to the surface.

Accu-Chek Performa

Item Description

This meter is the original Accu-Chek Performa meter – see the latest in the Accu-Chek Performa range here.

 

Accurate numbers help you to understand your diabetes and make informed lifestyle choices. That’s why Accu-Chek Performa has been designed to make extensive internal checks, giving you accurate results1,2, 3.

Product Manuals

DISPLAY

Large LCD

RESULTS

5 seconds

SAMPLE

Tiny: 0.6µL

WEIGHT

59g with battery

Benefits and Features
  • Large, easy-to-read display
  • Used with easy-to-handle Accu-Chek Performa test strips
  • Tiny blood sample: only 0.6µL of blood required
  • Fast results in 5 seconds
  • Fast fill strip quickly absorbs blood sample
  • Set up to 4 pre- or post-meal alerts, so you never forget to monitor
  • Automatically turns on when you insert a test strip
  • Saves energy by turning off automatically when you’re finished testing
  • Proven accuracy 1,2

 

References:
1. Freckmann, G., et al., J Diabetes Sci Technol 2012, 6(5):1060-75
2. ISO:15197: 2013
3. Accu-Chek Performa Test Strip Pack Insert, 2015

Additional Specifications
Serial number:

Unique serial number printed on a label on the device and stored in non-volatile memory 

Measuring time:

Approximately 5 seconds

Measuring conditions:

Temperature: 6°C to 44°C (46°F to 111°F) 

Storage conditions:

-25°C to + 70°C without battery

-10°C to + 50°C with battery

Memory capacity:

Up to 500 total results, plus 20 control tests

Test averages:

7, 14,  and 30 days

Data transfer:

Infrared (IR) window

Dimensions:

94 x 52 x 21 mm 

Weight:

62 g with battery

Display:

Large LCD display with symbols 

Beep tone:

Yes (factory setting ON)

Battery:

1 battery, 3V coin-cell type CR2032 

 

WARNING - KEEP BATTERIES OUT OF REACH OF CHILDREN. If you suspect your child has swallowed or inserted a button (coin cell) battery immediately call the 24-hour Poisons Information Centre
on 13 11 26 for fast, expert advice.

Battery life:

Approximately 2,000 measurements

Auto power off:

After 2 minutes undisturbed with strip inserted, or if powered on but left undisturbed for 2 minutes

Auto power on:

with strip insertion

Underdosing detection:

Yes

Sample size:

0.6 µL

Measuring range:

10 mg/dL – 600 mg/dL
0.6 mmol/L – 33.3 mmol/L

Sample dosing:

Capillary fill function

Hematocrit range:

10 to 65%

Test strip stability:

18 months after production date; test strips remain stable up to expiry date printed on test strip vial, even after opening (test strip container must be closed tightly after each test strip is removed)

How to use the Accu-Chek Performa blood glucose meter

Get results in 3 steps:

  1. Insert your test strip into the meter and it turns on automatically.
  2. Apply your blood sample to the easy-to-see yellow window. Only 1 small drop is needed.
  3. In approximately 5 seconds, your test results will appear in the easy-to-read display.